The Quadrino Multirotor Controller is a ready-to- fly controller based upon the open source MultiWii multirotor project. The code is continuously being updated by a large community of great programmers, so you will always have the latest capabilities. The Quadrino includes the highest accuracy sensors available and can be upgraded with additional sensors such as GPS.
The Quadrino includes the Arduino micro-controller, Gyro, Accelerometer, Barometer, Magnetometer and on-board usb interface. Plugin your radio receiver channels and ESC motor wires and you are ready-to-fly. It supports all MultiWii features such as auto-level mode (acc mode), heading hold (mag mode), and altitude hold (baro).
All the code is Arduino based and ready for you to modify for your custom project.
The Quadrino and MultiWii software supports a variety of flight modes.
Acrobatic Mode is really just flying without any features enabled. This is where you are in the most control of the flight response. When you are an experienced flyer you will probably fly most often in this mode doing flips, barrel rolls, deadman drops and full throttle horizontal flight!
Auto-Level Mode is where the copter's control system and sensors keep the copter level with reference to the direction of gravity. In this mode, if you do not give any input to the roll/pitch stick then the copter will remain level "on plane" at all times even if pushed by a gust of wind. Keep in mind though this is not position hold. Wind or other influence could still push the copter in any direction, but the copter will return to a level orientation. In contrast, a gust of wind in acro mode could cause the copter to bank or pitch.
Compass Hold (MAG hold) when enabled will keep the copter pointing in the same compass direction. You can still YAW, changing the copter's heading, and the copter will then maintain the new heading. This is great for beginner flyers, they can concentrate on the throttle, roll and pitch without worrying about maintaining the copter's heading.
Head free (Care free) mode uses the compass and your last known position to transform the commanded stick input from your transmitter from the perspective of the copter into the perspective of you, the pilot. For most beginner pilots the toughest part of flying is projecting yourself onto the copters orientation so that you can determine how you need to move the control stick. You have to imagine that you are sitting on the copter and facing the same direction. Head free mode removes this burden! The copter control software, knowing where you are, adjusts the stick input so that roll left is always left on the copter from your perspective and roll right is always right, and the same with the pitch. You take away the notion of a "front" on the copter, there is no front anymore!
Optional Flight Modes
GPS Position Hold enhances the auto-level mode to also keep the copter in the same position. It will bank the copter in order to counteract any external force such as wind. Now when you enable this feature the copter stays in one spot!
GPS Return to Home (RTH) when enabled will take full control of the copter, turning it toward the home position and then flying on its own back to the set home position. The home position is set each time the copter motors are armed. Lost orientation of the copter? Lost sight of it? Turn on the GPS RTH and it will come right back to you. Hopefully, there are no trees or low flying planes in the way! It isn't that smart.
Bluetooth RemoteEasily adds Bluetooth or 3DR radio and control features and parameters of your copter while in flight! Get fancy heads-up displays with telemetry, power output, GPS+GoogleMap and more. Also control flight parameters while in the air including Position & RTH control parameters. I recommend an Android tablet or phone but you can also use your laptop. If you plan on using a laptop then use the 3DR radios, they are easier to use and work better. Otherwise, with Android we are left with only Bluetooth as a choice since they do not support external radio links.
The Quadrino has a few features that are unique to other MultiWii boards. The most appreciated feature is the EZ-Connect wiring system that makes the initial setup of the flight control board on your copter much easier. This special cable provides the typical 3-pin RC socket headers that connect directly to the ESC inputs. The cable will source power from the first ESC by default. A second cable connects directly to your receiver using single pin female headers. Swapping Quadrino boards using the EZ-Connect system is so easy some people are purchasing an extra set of EZ-Connect cables and sharing the flight controller between many quad frames!
USB Protection Diodes
The Quadrino contains some extra diodes to prevent USB power from going to the motor ESCs. This prevents some cases where the motors might throttle up while you are configuring your quad. Most boards do not have these diodes. If you want to bypass this protection, heaven forbid, you can use an alternate protection-less power input.
Logic Level Converters
Integrated logic-level converters are placed between the sensors and the main microprocessor. These allow the main microprocessor to communicate with the sensors at the highest possible speed. Some boards simply use resistor dividers, make sure to look for "logic level converters" in any MultiWii board you buy else your sensor communication will be operating at a lower speed affecting the flight response of the copter.
Quadrino Multirotor Flight Controller
4 x Plastic standoffs for mounting the Quadrino to your frame
8 x Plastic screws
See our Quadrino Setup Guide for instructions.